Compressed air dryer maintenance method - Database & Sql Blog Articles

LC03-3.3 SOP8 TVS Static Protection 3.3V

Probe current voltage pin 420*4450 head diameter 5.0 over current current and voltage pin

How to maintain the compressed air dryer in daily production? How to maintain the compressed air dryer? Thanks to the above answerers. My problem is not explained. The dryer is a kind of equipment for drying and filtering compressed air. It is not an air compressor. I want to ask about the daily maintenance method of the dryer. Thank you. 2010-12-09 13:14 The questioner adopted the cold dryer according to the principle of freezing and dehumidification, using a fully enclosed compression refrigeration system to cool and cool the compressed gas discharged by the air compressor, so that a large amount of saturated water vapor contained therein, The oil mist condenses the droplets, which are discharged by the automatic drain after separation by steam and water. Proper use of the refrigerated dryer is an important prerequisite for obtaining the required dew point compressed air, saving regenerative energy and extending the life of the equipment. Cold dryers are rarely used alone, and in almost all pneumatic networks, the dryers are used with filters. This is not only the need to meet the quality of the gas, but also the normal operation of the refrigerated dryer itself. The refrigerating dryer is reliable, easy to manage, and low in operating cost. It is also an essential auxiliary equipment for the ozone system. The following is a brief introduction to some common knowledge of the daily maintenance of the dryer: 1, often observe the drainage, sewage system 2, often observe the cooling water system, compressed air system inlet temperature 3, often observe the refrigeration system 4, check the electrical control system: purge Dust tighten the terminal (must be carried out without electricity) Through the above knowledge, we should have a better understanding of the dryer, which is helpful for the use and maintenance of the dryer.

Micro Vibration Motor

The micro Vibration Motor is introduced:

Micro vibration motor is mainly used for adult health care products and toys, micro vibration motor is a Dc Motor, the motor shaft with an eccentric wheel, the use of most of the micro vibration motor voltage is lower than 6 v, probably between 6 mm to 15 mm in diameter, when the motor rotation, eccentric circle particles is not the core of the motor, the motor often lose their balance, due to the inertia effect.

Characteristics: small volume, strong vibration;

Features: small size, fast speed, stable performance, low price, can use battery drive,Can change the different materials of the pendulum head

Method of use: the best stable in horizontal plane, installed on the dc Micro vibration motor output shaft parts, cannot use a hammer to knock, knock prone to press into the Micro vibration motor drive, may cause damage to internal components, and cannot be used in the case of blocked.

Operating temperature range:

Mini Vibration Motor should be used at a temperature of -10~60℃.

The figures stated in the catalog specifications are based on use at ordinary room temperature catalog specifications re based on use at ordinary room temperature (approximately20~25℃.

If a Mini Vibration Motor is used outside the prescribed temperature range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.Depending on the temperature conditions ,it may be possible to deal with them by changing the grease of the motor's parts.Please feel free to consult with us about this.

Storage temperature range:

Mini Vibration Motor should be stored ta a temperature of -15~65℃.

In case of storage outside this range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.

Service life:

●Use with a load that exceeds the rated torque

●Frequent starting

●Momentary reversals of turning direction

●Impact loads

●Long-term continuous operation

●Forced turning using the output shaft

●Use in which the permitted overhang load or the permitted thrust load is exceeded

●A pulse drive ,e.g.,a short break,counter electromotive force,PWM control

●Use of a voltage that is nonstandard as regards the rated voltage

●Use outside the prescribed temperature or relative-humidity range,or in a special environment.

●Please consult with us about these or any other conditions of use that may apply,so that we can be sure that you select the most appropriate model.

when it come to volume production,we're a major player as well .each month,we rurn out 600000 units,all of which are compliant with the rohs directive.Have any questions or special needed, please contact us, we have the engineer group and best sales department to service to you Looking forward to your inquiry. Welcome to our factory.

Micro Vibration Motor,Mini Vibration Motor,Dc Micro Vibration Motor,Electric Micro Vibration Motor

Shenzhen Shunchang Motor Co., LTD. , https://www.scgearmotor.com