Fingerprint Lock Motor introduction:
Basic security work, lock body responsible for the security door lock body responsible for opening and closing lock, the lock body Lock Motor is of crucial importance.
Functions: it is widely used in various intelligent locks, such as Shared bicycle lock, fingerprint lock, glass lock, safe lock, hotel lock, family lock, inductive smart lock, etc
Features:Fingerprint Lock Motoris based on micro precision reducer development, small intelligent micro precision reducer can do 10 mm in diameter, is widely used in safe, locks, smart locks, sensor intelligent lock;
This kind of motor has the characteristics of low noise, low energy consumption, small volume, light quality, high precision, large torque and durability
Method of use: the best stable in horizontal plane, installed on the Fingerprint Lock Motoroutput shaft parts, cannot use a hammer to knock, knock prone to press into the dc Fingerprint Lock Motor drive, may cause damage to internal components, and cannot be used in the case of blocked.
Operating temperature range:
lock motor should be used at a temperature of -10~60℃.
The figures stated in the catalog specifications are based on use at ordinary room temperature catalog specifications re based on use at ordinary room temperature (approximately20~25℃.
If a lock motor is used outside the prescribed temperature range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.Depending on the temperature conditions ,it may be possible to deal with them by changing the grease of the motor's parts.Please feel free to consult with us about this.
Storage temperature range:
Fingerprint Lock Motor should be stored ta a temperature of -15~65℃.
In case of storage outside this range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.
Service life:
â—Use with a load that exceeds the rated torque
â—Frequent starting
â—Momentary reversals of turning direction
â—Impact loads
â—Long-term continuous operation
â—Forced turning using the output shaft
â—Use in which the permitted overhang load or the permitted thrust load is exceeded
â—A pulse drive ,e.g.,a short break,counter electromotive force,PWM control
â—Use of a voltage that is nonstandard as regards the rated voltage
â—Use outside the prescribed temperature or relative-humidity range,or in a special environment.
â—Please consult with us about these or any other conditions of use that may apply,so that we can be sure that you select the most appropriate model.
when it come to volume production,we're a major player as well .each month,we rurn out 600000 units,all of which are compliant with the rohs directive.Have any questions or special needed, please contact us, we have the engineer group and best sales department to service to you
Looking forward to your inquiry. Welcome to our factory.
Fingerprint Lock Motor,Motor For Fingerprint Lock,Gear Motor For Fingerprint Lock,Dc Motor For Fingerprint Lock Shenzhen Shunchang Motor Co., LTD. , https://www.scgearmotor.com
Panasonic said that as of the end of July, the company's LED bulb products totaled 48 models, while the incandescent bulb products have dropped from the 207 in 2008 to the current four. Panasonic's competitors in the lighting market, Toshiba and Mitsubishi Electric, have also stopped producing incandescent bulbs.
Since the production of incandescent bulbs in 1936, Panasonic's production of incandescent bulbs has reached 3.3 billion. In Japan's overall power demand, lighting accounts for 20% of the total, so if the lighting products are converted into LED bulbs or energy-efficient fluorescent lamps, the power demand can be greatly reduced. At present, in Japan's overall lighting market, the proportion of products with low energy efficiency is still as high as 60%. 
Panasonic Announces Discontinuation of White Hot Light Bulbs at End of October to Accelerate LED Bulb Popularization
On July 12, Panasonic announced that the lineup of energy-saving products such as LED bulbs used to replace incandescent bulbs has become more complete, and the Japanese government proposed to manufacturers and retailers to accelerate the popularization of LED bulbs in June. The resolution was discontinued on October 31, 2012 for the white light bulb products used in general households. The production stoppage time will be half a year earlier than the originally planned March 31, 2013.