In incandescent delisting other lighting replacement period, in fact, consumer LED lighting is not the absolute resistance, but did not dare to accept. At present, product identification on the LED market is not clear and unclear, and there is also a lack of uniform standards. Faced with jagged products, the Guangdong Provincial Bureau of Quality and Technical Supervision recently conducted spot inspections of LED lighting products.
In this investigation, self-ballasted LED lamp products produced by 21 companies in 7 cities including Guangzhou, Shenzhen, Zhuhai, Foshan, Zhongshan, Huizhou, and Dongguan were used. A total of 23 batches were tested, and 17 batches of unqualified samples were tested. The pass rate was less than 30. %. It is understood that there are many LED market companies scattered, the brand may be as many as thousands, but there are not many real trustworthy brands, industry experts said: "30 yuan product quality is difficult to guarantee."
For current LED lighting products on the market, experts put forward purchase suggestions:
First, look at the product packaging: see if there are product trademarks and certification marks, such as: 3C certification, CE certification, etc., in addition to see if clearly marked the product's rated voltage, voltage range, color temperature, precautions, safety instructions, applicable environment, etc. .
Second, the price comparison: due to the special reasons in the production process of LED lamps, the cost is relatively high, the general domestic LED lamp prices are more than forty or fifty yuan, the import is even higher. In addition to looking at the appearance of the product is not rough, is there no glue is not clean, whether there is a screw protruding plane? Whether the color of the screw is consistent with the color of the shell.
Third, the light after lighting need to carefully observe the lamp color changes, if in a short time, from yellow to white, or from white to blue with white light, such products will have to give up, because There are two possibilities for this situation: one: the power supply problem; two: LED light source selection errors. In addition, the color of the light must be positive, and the light color of the light is the same, ie it does not flash. After the LED lamp is turned on, it can detect the heat dissipation of the product by touching the surface temperature of the product. If the temperature of the product surface continues to rise in one hour, instead of being stable for the longest time in 30 minutes, the product should not be selected due to heat dissipation. , resulting in shortened product life.
4.2mm Wire To Board Connectors
4.2mm Wire To Board Connectors are avialable in different terminations and sizes intended for use on a variety of applications. These connectors provide power and signal with different body styles, termination options, and centerlines. To find the wire to board set required, click on the appropriate sub section below.
4.2 mm pitch connectors wire to board connectors
Fully isolated terminals, positive locking housings, low-engagement forces and polarized housings, also offers blind mating, TPA and higher current options. Pitch 4.20mm
4.2 mm pitch connectors wire to board connectors Including:
male housing
Male housing of connector, UL94V-0 and UL94V-2, hanging and panel mount, single row and dual row, 2 to 24 circuits.
Female housing
Female housing of connector, with locking latch in order to avoid loosing, and with polarity in order to avoid dis-mating. One row and dual rows, from 2 circuits to 24 circuits.
Terminal
The conductor of connector, brass or phosphor bronze, tin plated over nickel, selective gold plated as customer's requirement.
Header
Header, right angle and vertical , with peg and without peg, DIP soldering, single row and dual row, 2 to 24 circuits.
4.2 mm connectors wire to board connectors General Specification:
Current rating: 6A AC, DC.(AWG#18)
Voltage Rating: 600V AC,DC
Withstanding Voltage: 1500V AC/minute.
Insulation resistance: 1000MΩ min
Contact resistance: Initial Value/ 10mΩ max
Temperature rise: -40'C ~ 105'C.
Circuit Board Connectors,4.2Mm Wire To Board Connectors,4.2Mm Pcb Wire To Board Connector,4.2Mm Pin Wire To Board Connector,.165" Wire To Board Connectors,4.2mm Power Connector
ShenZhen Antenk Electronics Co,Ltd , https://www.antenksocket.com