3.0mm Wire To Board Connectors
3.0mm Wire To Board Connectors are avialable in different terminations and sizes intended for use on a variety of applications. These connectors provide power and signal with different body styles, termination options, and centerlines. To find the wire to board set required, click on the appropriate sub section below.
3.0mm Wire To Board Connectors Type
3.0mm Terminal
3.0mm Wire To Board Connectors Advantages
Pcb Connectors Wire To Board,3.0Mm Wire To Board Connectors,3.0Mm Pcb Wire To Board Connector,3.0Mm Pin Wire To Board Connector ShenZhen Antenk Electronics Co,Ltd , https://www.antenkwire.com
In March 2008, Adek built a new office building that will LED all outdoor lighting. The actual office building is used as a place for customers to experience the LED lighting fixtures and lighting systems they manufacture. The same effect.
The company said that although it is also related to the installation site, it can reduce the power required for lighting to less than half of the original, and will not affect the production efficiency of the factory. Because it is an empirical experimental field, it can not only promote the products to potential customers of LED lighting systems, but also can control the lighting, turning off and lighting only part of the lighting of the LED lighting for the platform to develop high commodity value. LED lighting system.
The LED lighting fixtures set up by the Adeksano Business Center are 225 units instead of straight tube type fluorescent lamps, 36 units for substitutes, and 4 units for mercury lamps, totaling 265 units. A total of 1,481 lighting fixtures were used throughout the Sagano business, and the adoption rate of LED lighting fixtures was approximately 18%.
The LED lighting of the Takino business center will be concentrated in specific offices and production lines, and the installation facilities in the automatic assembly line of push buttons, switches and relays, etc., all of which are designed for use in LED technology, all of which have been implemented with LED lighting. Production equipment and LED lighting."
At present, the second floor of the new building of the Takino Plant, where the automatic assembly line is located, has reduced the amount of electricity used for lighting by about 50% by replacing fluorescent lamps with LED lighting. By using LED lighting linked with human sensors, power consumption has been reduced. Less than half of the original 28 to 40%. In terms of cost, the total value of the initial cost (lighting device fee, installation fee) and operating cost (electricity fee, maintenance fee) is lower than that of the FL type when the LED lighting fixture without the dimming function is used. Fluorescent lamp, Hf-type ordinary fluorescent lamp with lower energy efficiency after 4.4 years. When using high-priced LED lighting fixtures with dimming function, it can be lower than fluorescent lamps after 5 years and 6.4 years.
At present, Japanese LED bulbs are becoming more and more popular, which will lead to the expansion of LED lighting to production sites such as factories. 
3.0mm Housing
Pitch 3.0mm Wafer Right Angle&SMT Type
3.0mm Wafer Straight Type
3.0mm Wafer SMT Type
3.0mm Wafer Right Angle Type
3.00mm Wafer Single Row Straight Type
3.00mm Wafer Single Row SMT Type
3.00mm Wafer Double Row Straight Type
3.00mm Wafer Double Row SMT Type
3.00mm Wafer Double Right Angle Type
3.00mm Wafer Double Right Angle&SMT Type
Small electronics with high current requirements
One of the strongest advantage of the Micro Fit series is its applicability in delivering the high current requirement in electronics with supplying high power.
Safe and Reliable
ensure safety, system protection and performance with its bonded metallic conduits and multiple grounding points preventing fire hazards, component damage, overheating and possible electrocution.
ROHS Compliant
The product does not contain restricted chemicals in concentrations not complying with ROHS standards. Thus, for its components, the products can be worked upon at high temperatures required by lead-free soldering.
3.0mm Wire To Board Connectors Application
Motherboard Connectors
The Motherboard of a computer holds together many of the crucial components such as the central processing unit (CPU), memory and connectors for input and output devices. Microfit connectors ensure high performance electronic system in quality motherboards.
You can easily find Scondar`s Microfit in most ITX Motherboards, in which its functionality is best described for solid performance in a small footprint, and low power consumption (less than 100 Watts).
Printer Connectors
The 3.0mm Microfit can also be seen in most printers
Automotive PC Connectors
Smart, high power automotive PC power supply garners its capabilities from quality Microfit connectors, designed for general purpose battery powered applications. These are manufactured to provide power and to control the motherboards' switch based on ignition status.
Solar Panels
Microfit can also be commonly found in a solar array. A solar array is connected to each other, and to inverters through connectors to produce a successful flow of electricity.
Japan Aideke demonstration factory LED lighting energy saving effect
[High-tech LED News] Recently, the Japanese factory Idek (IDEC) has implemented the renovation of the lighting of its wilderness business, and fully demonstrated its actual use by using its own factory as an "experimental experimental field for LED lighting in factories". Increase the energy-saving effect of the environment, and increase the customer's purchase of LED lighting fixtures and control systems for the factory.