Introduction of DS1847 for industrial control-Introduction of

Abstract: This applicaTIon note introduces the DS1847 and DS1848, dual digital temperature-controlled variable resistors, to the industrial controls market. By temperature compensaTIng the resistors, the resistors can either remain at a specific resistance or vary over temperature by programming a unique resistor value every 2 ° C. The DS1847 can also be used to control voltage or current. The DS1847 and DS1848 are idenTIcal except the DS1848 includes addiTIonal user programmable EEPROM. In this application note, DS1847 will refer to the DS1847 and DS1848.

This application note presents the DS1847 features and operation in addition to some application ideas. To discuss how the DS1847 can benefit your application, please contact Applications Support at var name = "MixedSignal.Apps @"; var domain = "dalsemi.com"; document.write ("" + name + domain + ""); MixedSignal ..

DS1847 FeaturesFigure 1 shows a block diagram of the DS1847. The DS1847 operates from a 3V or 5V supply over the temperature range of -40 ° C to + 95 ° C and offers internal closed loop temperature compensation.

Figure 1. Block diagram.
Figure 1. Block diagram.

The DS1847 can operate standalone in closed loop mode without a microcontroller or with a microcontroller using an optional 2-wire master. The 2-wire master allows multiple devices to be controlled in different locations.

Figure 2 shows how multiple DS1847s can be connected to a 2-wire master. The address pins allow up to 8 devices on the 2-wire bus.

Figure 2. 2-Wire interface.
Figure 2. 2-Wire interface.

Temperature CompensationOne of the benefits of the DS1847 is the internal closed loop temperature compensation. Since the resistor settings and memory are nonvolatile, a microprocessor is not needed when using the DS1847.

With the ability to program the resistance as a function of temperature, the user can create a very low tempco resistor. The compensated tempco error is ± 4 LSB. A transfer function can be programmed into the resistor lookup table (LUT) to fit many applications The resistor LUT is EEPROM memory that can contain a unique resistor value at a specific temperature from -40 ° C to + 95 ° C in 2 ° C increments. See the DS1847 Operation section for more information on the LUT.

The resistor outputs can also be used as digital outputs to drive external circuitry. The outputs can be used as alarms or as general-purpose digital outputs. The DS1847 can be configured to output a resistance, voltage, or current.

DS1847 OperationThe DS1847 has a LUT that determines the resistor value at a specific temperature (see Figure 3). First, after a 10ms conversion time, the internal temperature sensor senses the ambient temperature. This temperature determines the LUT address. If the temperature sensed is -38 ° C, the corresponding address is 01h. The resistance value in address location 01h is used to adjust the resistance.

Figure 3. Lookup table.
Figure 3. Lookup table.

Using the DS1847 with Industrial ControlsThe DS1847 can be beneficial in industrial control applications. First, the temperature-controlled resistor can provide a relatively constant resistance over temperature or the resistance can be set to increase or decrease with temperature.

Figure 4 shows how the DS1847 can be connected to a fixed resistor to create a voltage divider (Vout0). This will provide a fixed or variable output voltage to an application over temperature. A transfer function can be programmed into the LUT to change the voltage with temperature.

Figure 4. Voltage and digital outputs.
Figure 4. Voltage and digital outputs.

The DS1847 can also be configured to create a digital output (Vout1). Using a fixed resistance of 4.7kΩ and the 50kΩ variable resistor, the output voltage range is 0.77V to 4.57V (see Example 1). The digital output can be used as an alarm or warning when the temperature reaches a certain value (see the Voltage Alarm Example). The digital output can be set to go low or high if the temperature changes from the set value or if the temperature exceeds a certain value.

Voltage Alarm ExamplesTo set the voltage to go high when a specific temperature is reached, 94 ° C in this illustration (see Figure 5), the LUT would be programmed to set the resistor to the minimum position (position 0) for the temperature range- 40 ° C to 92 ° C. For temperatures 94 ° C and above the resistor position would be set to FFh.

Figure 5. Lookup table for a voltage alarm.
Figure 5. Lookup table for a voltage alarm.

Design ConsiderationsWhen using the DS1847 as a voltage divider or a digital output, the fixed resistor value needs to be calculated (see Figure 6).

Example 1.
If the DS1847 will be configured as a digital output, the output voltage needs to meet the VIH and VIL levels of the digital circuitry. Equation 1 shows how to calculate the output voltage at a certain fixed resistance.


Equation 1

Where, Vin = Vcc = 5V
Rv = DS1847 50kΩ resistor (Rmin = 850Ω, Rmax = 50kΩ)
(Notice that the minimum resistance at position 0 is not 0Ω but 850Ω.)
Rf = Fixed resistor

Figure 6. Voltage divider.
Figure 6. Voltage divider.

Using Equation 1 and the Rmin and Rmax of the 50kΩ resistor, the output voltage range is calculated.



Using a 4.7kΩ resistor, the output voltage range is 0.77V to 4.57V over the resistor range of the 50kΩ resistor.

ConclusionsThe DS1847 and DS1848 have many features that would be useful in industrial control applications. The variable resistors could easily replace a mechanical potentiometer and provide additional features. The DS1847 and DS1848 are able to perform multiple functions in one small package including temperature compensation. The DS1847 and DS1848 can be used standalone or with a microcontroller. To discuss your application, email Applications Support at var name = "MixedSignal.Apps @"; var domain = "dalsemi.com"; document.write ("" + name + domain + ""); MixedSignal ..

TPU Screen Protector

Navigating Digital Clarity with HD Screen Protectors
As digital integration deepens, the demand for pristine screens on our devices has never been more evident. High-Definition Screen Protectors stand as stalwarts against damage, ensuring our interactive windows to the world remain unblemished and vivid.
The Essential Shield: HD Screen Protector
An HD Clear Screen Protector is an essential tool against the onslaught of daily threats our devices face. These guardians fight off the common culprits of screen damage-keys, drops, and the continuous contact of our fingertips-while ensuring the display's integrity.
Enhanced Visibility with High-Definition Screen Protectors
Beyond safeguarding against physical damage, High-Definition Screen Protectors play a pivotal role in enriching our visual interaction. They are the unsung heroes that maintain the dynamic range of colors and detail necessary for an optimal viewing experience, whether gaming, leafing through photos, or streaming.
Clarity Preserved: Fusing Protection with Transparency
With the goal of delivering clear protection, HD Screen Protectors are crafted to be Transparent Screen Films, upholding the screen's original luminosity and detail. Their near-invisible presence coupled with their protective properties results in a shield that doesn't distract from the beauty of the screen but rather enhances it.
Touch Sensitivity Untouched: HD Clear Screen Protector
The HD Clear Screen Protector is also keenly designed to maintain touch sensitivity. Every interaction, from navigating menus to executing gestures, is as intuitive and responsive as it would be on an unprotected screen, ensuring the digital experience remains fluid and natural.
Tough Yet Invisible: Transparent Screen Film
Not just a clear overlay, Transparent Screen Film is a synonym for toughness, ready to tackle the sharp edges and rough surfaces that threaten your screen's pristine condition.
Finding Your Ideal HD Screen Protector
In choosing your HD Screen Protector, consider these factors to guarantee you get a product that fits not just your device, but your lifestyle as well:
Device Specificity: Match the protector with your device for exact coverage and uncompromised aesthetics.Material Matters: Match your needs with the right materials-whether it's the classic tempered glass or a modern TPU variant, find the balance between protection and clarity that works for you.Embodying Screen Perfection
The integration of an HD Screen Protector into your digital ecosystem equates to embracing both clarity and resilience. From a variety of choices, an HD Screen Protector stands out as a straightforward, reliable selection for those who prioritize seamless functionality along with crystal-clear display quality. Transform your device's resilience and retain the joy of a luminous, crisp screen by choosing the right High-Definition Screen Protector.

Hd Screen Protector,High-Definition Screen Protector,Hd Clear Screen Protector,Transparent Screen Film

Shenzhen TUOLI Electronic Technology Co., Ltd. , https://www.hydrogelprotectors.com