Nowadays, LED has quickly occupied the market in various indoor commercial spaces due to its many superior features, and has become the mainstream of commercial space lighting. Traditional ceramic gold halides are withdrawing from the historical stage due to their high power consumption, difficulty in starting, fast light decay and short life. However, due to the rapid development of LEDs and the special light of LED light sources, as well as the lack of understanding of lighting knowledge by various users, LEDs should be used in indoor commercial space. Many practical problems are still emerging, so many users apply LEDs. The high-end commercial chain space is still skeptical. The following small series will use Suzhou Yalu clothing (men's clothing, high-brightness lighting demand) as a case to analyze the design and application of LED lights in high-brightness indoor commercial lighting. When Xiaobian went to the store for inspection, the store manager had been complaining about the quality of the lamps with Xiaobian, the lights were few, and the store was not bright enough. Xiao Bian also felt that it was not bright enough at the time. In order to understand the actual problem more clearly, Xiaobian was accompanied by the manager, and scanned the product with a keen and sharp professional look at the lamp. The result was that the store’s merchandise was not found. The highlight is. What was discovered later was the layering of light on the ground, which was both messy and bright. The result of the judgment is that the light is not bright enough, nor is the lamp not enough, but the lighting method is problematic, and the light is not used to the place of utilization. Seeing this, Xiao Bian really can't stand it anymore. Decisively ask the store manager to provide a ladder and personally climb the ladder to re-adjust the lamps in the entire store. Move the mid-field part of the over-density luminaire to the side field, re-position the luminaire's projection orientation, and find out the zoning display rules of the hanging, side-hanging and model. The principle of zoning is adopted. The result is a series of major adjustments and planning. After the completion, the lighting effects immediately showed a big difference from the previous ones. Even the store manager praised the lights and the second. (The shop uses rail spotlights, it is more convenient to adjust). The following picture shows the brightness of the shop before the adjustment. You can see that the side field and the midfield are not bright enough. It is difficult to find the highlights after the customer enters the market (find the goods that the customer needs): The following picture shows the field in the side field during the adjustment process. As the projection point is adjusted, the brightness of the side field and the midfield is obviously changed: The reason for the investigation is as follows, because the shop side cabinet is almost the same height as the floor. The installation distance between the luminaire and the side cabinet is obviously too close. The field test is only 600mm. Through the analysis of the light projection diagram, it can be found that most of the light is projected onto the upper display of the side cabinet, while the lower display of the side cabinet has almost no light. See the diagram for details: Adjusting the relationship between the front side cabinet spotlights and the side cabinet display Because the installation position of the on-site luminaire has been fixed, the problem of the dull side cabinet being dull due to the too close distance is solved. After the in-depth analysis, Xiaobian can only project and illuminate through the interlacing of lamps and mutual light. This can make the spot coverage of the spotlight larger and more efficient, which can improve the overall brightness of the side cabinet. See the adjusted real-life map, it is obvious that the brightness has increased by at least 50%. In fact, there is a technical problem extended here. As the designer or the construction personnel are dealing with the side cabinet lighting, we usually need to pay attention to the distance ratio between the side cabinet and the lamp installation. Generally, the principle of 1/3 multiplied by 0.8 coefficient is adopted. Handling the relationship between side field luminaires and layer height. That is, when the floor height is 3.2 meters, we generally take the distance of the edge field lamp from the surface of the side cabinet to 1.066 meters and multiply by the coefficient of 0.8, which is 0.85 meters, which is the most appropriate. At this time, the display lighting of the upper and lower side cabinets is ideal, but there is still a part of the lower side cabinet, which does not affect the sales, but does not affect sales. If you want to achieve the best, you can find out through the schematic diagram that it is best to take 1 meter, and the upper and lower sides of the cabinet display can be balanced, but there is a problem. When the customer chooses clothes, it is easy to hit the customer's head or the back of the head, which is easy to cause. Customer discomfort and shadow of the side cabinet. At the same time, this distance will be too far away, making it difficult to balance the display of the Nakajima area. At present, the COB -type LED light source is currently referred to as 85 or more, and the luminous efficacy is basically around 85Lm. This effect is basically consistent with the indication and light effect of the ceramic metal halide light source, that is, now the 1 watt LED can completely replace the 1 watt ceramic metal halide lamp, and the brightness is basically consistent or even exceeded. However, the current maximum wattage of LEDs can only be 35W, while the power of ceramic metal halide lamps is 70W. Therefore, if one-to-one replacement is used, it is impossible to achieve the effect of ceramic gold halide brightness. Therefore, to achieve the effect of gold halide brightness, we can solve the problem by increasing the number of LED lamps. In fact, this does not affect the overall operating cost, but the initial The investment cost will be slightly higher than the initial cost of using a ceramic gold halide source. Many merchants have seen it here, and they feel that it is not worthwhile to use LED lamps. Actually, it is not. By analyzing the following data, we can see that the initial cost of LED is high, but after three years of use, the overall investment and maintenance operation cost is lower than the overall operating cost of the ceramic metal halide lamp, and Still quite a lot. Take Yalu men's clothing as an example. After three years, the total operating cost of a single store is 63,700 more than that of LED lights. Many merchants saw that the amount of 6.37 million was not large, but when it counted 10 stores? 100 stores? 1000 stores? In fact, from another perspective, from the perspective of market sales, as a supplier, Xiao Bian believes that it is not simply to sell the products that customers need to customers to complete the business. What needs more thinking is how to think about the problem from the perspective of the customer. For example, how can we help customers to sell products sold to customers? How can we help customers maximize the use of products? How can we save operating and maintenance costs more effectively for customers? The sales strategy of such a complete service plan. This sales strategy editor believes that it is much longer than simply selling the product to the customer, which in turn can be understood as a question of how the supplier can effectively convert the free technical service provided by the brand manufacturer into a sales value-added strategy.
SMD2835 LED Strip Light is the power lamp beads SMD super bright LEDs with 0.1W 0.2W and 0.5W. 2.8 because of its size (length) × 3.5 (width) × 0.8 (thickness) mm, according to post solid piece LED lamp beads Size naming, named 2835 lamp beads. 2835 warm white / white (2700-6500K): 20-22 lumens luminous flux SMD 2835 3014 is the second after the upgrade, the overall performance is better, more competitive. 2835 circuit board and is not the same as the 3528, but also can replace the use of brightness, heat better than 3528.
SMD 2835 LED Strip Light of the light source LED2835 lights. SMD chip type genus, the carrier is a soft FPC board. That flexible circuit boards, most of the width of 8MM, thickness of less than 1MM. Each FPC factory length of 0.5 meters. Can be two or several mutually welded. Produce a good SMD 2835 Led Strip Light of the length of the factory 5M roll, anti-static disc and anti-static bag, portable and easy to transport.
SMD 2835 LED strip light can be classified from the following aspects:
We focus on LED area, is a high-tech lighting enterprise deal in develop, produce and sales.
Our R & D team can handle highly customized designs and offer OEM and ODM services.
SMD2835 LED strip light packing:
Smd2835 Led Strip Light,Computer Led Strips,White Light Strip,Motorcycle Led Lights Shenzhen Mingxue Optoelectronics CO.,Ltd , https://www.led-lamp-china.com
1. Color: FPC main color yellow board, whiteboard, blackboard, can be customized. SMD 2835 LED strip light luminous colors as same as ra90 led strip: white, warm white, red, yellow, blue, green, purple.
2. Waterproof: SMD 2835 LED strip light due to apply to a different location, waterproof grade is divided into not waterproof, Epoxy waterproof, waterproof casing.
3. Lamp beads: on the FPC can be attached to many SMD 2835 LED strip light lamp beads, so the per meter FPC, lamp beads per meter 30 lights, 60 lights per meter, 120 lights per meter three general to apply to different brightness requirements The place.
Owns DIP LED,SMD LED professional production lines and LED lighting products lines, the produce volume per month for DIP LED,SMD LED is 50 million pieces, forSMD 2835 LED strip light is 500 thousands meters, for LED flexible strip light for car is about 200 thousands pairs, for LED tube light is 50 thousands pieces, for LED Spotlights are 200 thousands pieces, for LED ceiling light are 50 thousands pieces.
Mingxue Optoelectronics Co.,Ltd. has apply the I S O 9 0 0 1: 2 0 0 8 international quality management system certificate, we apply the CE, RoHS and SAA certificate for our led lighting product.
We hope to set up a long-term partnership with you through our high quality products and our Sincere Service!
